Motorcycle Suspension Setup: Getting to Grips with a Black Art
Suspension Set-up: The basics
Whether you are a road rider or a racer correct suspension setup is the key to fast smooth riding and consistent lap times. To get the best out of your bike it needs to be set up for the conditions in which you will be riding. It is considerably easier to set the bike up for the Track as you know what conditions will be like for the next hour or so and thus you can dial in the optimum settings for the that particular situation.
To what extent you change your suspension settings will depend on whether your bike will also have to cope with riding on the road. Unlike Roads Tracks are generally smooth and grippy. So if you are only going to use the bike on the track you have the luxury of fitting harder springs and modifying the fork and shock internals. If you ride on the road as well as the track you will probably want to keep a certain comfort level and concentrate on just optimizing the current equipment
With incorrect suspension setup, tire wear is increased and handling suffers, which in turn can result in rider fatigue. Lap times can be dramatically slower and in extreme cases safety can be compromised. Hopefully the following guide will help you dial in your suspension for faster and safer riding both on and off the track.
Firstly you will need to check the Fork and Shock sag: this is the amount the forks and rear shock settle under load. To measure it do the following: push down on the forks a number of times to settle them, then mark the stanchion with a felt pen or put a cable tie where the dust seal is sitting. Next ask some for help to lift on the bars so the front wheel is just off the ground and measure the amount the forks have traveled down. This is the static sag (or unladen sag), This can be changed by adjusting the spring preload (more preload = less sag). Repeat the same process for the rear, this time measuring the distance from the wheel spindle to a fixed point on the tail. Now you are ready to begin setting up your suspension. The key is to do it a little at a time and make notes as you go. For road riding start with the wet track settings and work from there.
Basic Setup: Check the following
Forks sag 18-22 mm for dry track, 23-27mm for rain.
Shock sag 8-10mm for dry track, 10-14mm for rain.
Check chain alignment. If not correct, bike will crab walk and sprocket wear will be increased.
Proper tire balance and pressure, starting with 30psi front and 32psi rear (both dry and wet).
Steering head bearings and torque specifications - if too loose, there will be head shake at high speeds.
Front-end alignment. Check wheel alignment with triple clamps. If out of alignment, fork geometry will be incorrect and steering will suffer.
Crash damage, check for proper frame geometry.
Stock Suspension Tuning Limitations
Manufacturers plan on designing a bike that works moderately well for a large section of riders and usages. To accomplish this as economically as possible, they use valving with very small venturis. These are then matched to a very basic shim stack which creates a damping curve for the given suspension component. At slower speeds this design can work moderately well, but at higher speeds, when the suspension must react more quickly, the suspension will not flow enough oil, and will experience hydraulic lock. With hydraulic lock, the fork and/or shock cannot dampen correctly and handling suffers. The solution is to re-valve the active components to gain a proper damping curve. It does not matter what components you have, (Ohlins, Fox, Kayaba, Showa) matching them to your intended use and weight will vastly improve their action. Furthermore, if you can achieve the damping curve that is needed, it does not matter what brand name is on the component. Often with stock components, when you turn the adjusters full in or out, you do not notice a difference. In part, this is due to the fact that the manufacturer has put the damping curve in an area outside of your ideal range. Also, because the valves have such small venturis, the adjuster change makes very little difference. After re-valving, the adjusters will be brought into play, and when you make an adjustment, you will be able to notice that it affects the way the way the fork or shock performs.
Another problem with stock suspension is the springs that are used. Often they are progressive, increasing the spring rate with increased compression distance. This means that the valving is correct for only one part of the spring's travel, all other is compromise. If the factory does install a straight-rate spring, it is rarely the correct rate for the weight of the rider with gear. The solution is to install a straight-rate spring that matches the valving for the combined weight of the bike, rider and gear to the type of riding intended.
? Always make small adjustments, more is not always better.
? Always keep notes of what you have done.
? Suspension tuning is an art - be patient
Mark Thompson has spent the last 20 Years Racing motorcycles and managing Race Teams. He now runs the Trackbikes website.
It?s One Thing for People to Buy Your Product or Service, but It?s Another for Them to Tattoo Your
William Harley and Arthur Davidson, both in their early twenties, built their first motorcycle in 1903. During their first year, the company's entire output was only 1 motorbike; however, by 1910, the company had sold 3,200. Movies such as Easy Rider made Harleys a cultural icon and soon the company attracted people who loved its bad-boy mystique, powerfulness, rumbling voice, distinctive roar, and toughness. It sounded like nothing else on the road, and even Elvis Presley and Steve McQueen longed to ride one.
Ghost Minimoto Moto GP Reps ? What Are They?
What are Mini moto's? A Minimoto is a miniature version of a real GP racing motorcycle; it just doesn't go as fast as one. There pocket bikes are available in many different makes and styles, many of which look just like real racing bikes but in a miniture version such as those found on GhostRacingSeries website.
A Great Motorcycle Ride in Mexico: Queretaro
A beautiful ride across cities and places named World Heritage by the Unesco, through an splendid protected natural area and ending in a surrealistic garden by artist Sir Edward James. Just keep reading... The ride starts in Queretaro City at 5,970 ft above sea level.
Motorcycle Suspension Setup: Getting to Grips with a Black Art
Suspension Set-up: The basics
How To Make Your Own Vintage Motor Cycle & Automotive Spare Parts
Vintage Car & Motorcycle restoration enthusiasts all share one thing in common...
Common Mistakes Motorcycle Buyers Make When Looking For a Motorcycle Loan
Whether interest rates are high or low or it's the end of a model year with lots of incentives, motorcycle buyers tend to make the same mistakes when shopping for a motorcycle loan. Here are four common mistakes motorcycle buyers make with motorcycle loans.
Mini Moto Mayhem
Mini Motos have been around in the UK for around ten years now. The first bikes we're cobbled together with parts that were already available. Small 2 stroke engines, mainly from garden machinery, were used. This type of engine is still used today for a few models and is referred to as an 'industrial' engine. But now the mini moto has been given an overhaul and has taken off in popularity.
Motorcycle Protective Clothing That Works!
There is some great looking motorcycle clothing on the market these days, but believe me not all of the motorcycle clothing offers as much protection as you think. In Europe, for motorcycle clothing to be lawfully sold as "safety" clothing, it has to pass a series of European standards, which are pretty lengthy but are available on my website. The standards cover the clothing's performance in abrasion, tearing and impact tests, and when they have passed; they are sold with the CE mark. However, no such regulation is available in the USA, so what should you look for?
Kawasaki Motorcycles - Independent in Thoughts and Actions
The story of Kawasaki Company goes back to 1924, at that time involved into metallurgy and the aircraft industry.
Necessity of Motorcycle Parts
If you are one of the many people who consider your bike as invaluable as your family, then we know you're head over heels. We may be judged heavily for this perception but you might even be willing to dump your partner just so you could spend time riding and caring for your bike? though, we hope you are not that obsessed.
Suzuki Motorcycles - From Fine Loom Manufacturers to Major Motorcycle Company
Started in a small warehouse by Michio Suzuki back in 1909, Suzuki aimed at making better looms for the Japanese silk industry. It was only thirty years after its existence that the company started thinking of diversifying into cars, motorcycles and related machinery. In fact, it was only after the collapse of the cotton market in 1951, that Suzuki seriously got into the motorcycle and car industry.
So You Want To Be A Custom Bike Builder? Start With A Motorcycle Kit!
So you want to be a custom bike builder? Well friend, before you rush out and buy that motorcycle kit, the one that will set you on the road to riches and fame, stop and think about the level of expertise and artistry the top builders have attained. More importantly think about how long it has taken them to attain it! Let's look at a few key issues?
How to Remove Your Mk2 Mini Moto Engine
Many mini moto modifications will require you to remove the engine from the mini moto. This is why I have produced the following guide.
A Convenient Way to Slash Your Gas Bill
"With oil prices spiraling higher almost every day, people are starting to look for alternative modes of transport," says Michael S. Milstead of Scootertronics. "With scooters, commuters can slash their gas bills and still have an efficient, reliable mode of transport."
Motorcycle Radar Detectors
Standard radar detectors were not built for motorcycles and were never intended to be used on them. Most detectors use an audio device to inform the driver that radar had been detected, and are therefore inappropriate for motorcycle riders because they cannot be heard. Furthermore, most have long cords and poor mounting options, not to mention the fact that they are not weatherproof. As both motorcycles and radar detectors have become more popular, however, the demand for motorcycle radar detectors has increased dramatically.
Frame Slider Design and Selection
Call them crash protectors, crash bobbins, fairing protectors or frame sliders, all these products ultimately seek to do one thing - protect your expensive bodywork or the essential and often expensive structural parts of your motorcycle from damage in the even of a fall or tip-over. The frame slider concept is as old as the proverbial 'crash bar' and today there are as many designs and brands as there are models of bikes. The proliferation of these types of products testify to the success of the idea of providing a sacrificial item to absorb some of the damage in the event of a fall. We are by no means experts on this concept nor were we the first to come up with it, but in this article we hope to provide you with an unbiased view so that you can make an informed decision when you're ready to put down your hard earned cash.
People Are Crazy... and Everyone Is A Racer
?And everyone is a racer. If you doubt that, you've obviously never driven in New York City during rush hour. Look closely at the driver of that Japanese luxury car. He's just as miffed as you the racer is at having to drive fifty-five miles per hour when the speedometer on the car clearly reads one hundred and fifty. Why can't we drive it at that speed if the car can come close to it. Man, just look at him fiddling with the knobs pretending to be tuning the radio into a station. We racers know what he is really doing is setting the frequency of his imaginary laser beam roadblock remover system. You know the ones; they make little bomb sounds as we pretend we are obliterating our foes on the drive home.
Trackdays - Get the Maximum Enjoyment from Your Time on the Track
Many motorcyclists want to take their bikes onto the track and trackdays are the ideal environment. If you have never been on a track before the experience can feel daunting so here are a number of tips to help make your trackday enjoyable. Use a van or a trailer to get your bike to the track
Know Your Mini Moto
The Mini Moto is a small scale replica of the World Super Bikes used by the likes of Valentino Rossi and ex champion Carl Fogarty. The Mini Moto comes equipped with either a two stroke air or water cooled engine which are, depending on the model, capable of speeds of up to 60Mph.
0 to 60 in 4.5 Seconds
Speeding is illegal, yet we sell racing motorcycles and cars which are so powerful and look so intimidating that a police man could write the owner a ticket even if it were parked. Take today's crotch rocket, nearly all of these motorcycles can barely get out of second or third gear going sixty miles per hour. We complain when our teenagers drive these bikes like they are meant to be driven. Silly of us to think that anyone is going to drive these bikes and never speed?
|home | site map|